Expert HVAC solutions for homes and businesses across Kelso, WA. Certified technicians, transparent pricing, and results you can count on.
Professional HVAC solutions for residential and commercial properties in your community.
A professional HVAC inspection evaluates the complete system from furnace combustion and heat exchanger integrity to air conditioning refrigerant charge and electrical safety. Technicians document equipment age, efficiency ratings, and any code violations to give you a clear picture of system health.
Preventive furnace maintenance protects your household by identifying cracked heat exchangers, carbon monoxide risks, and failing ignition components before they cause a breakdown. Annual service preserves rated AFUE efficiency and ensures consistent airflow through cleaned blower assemblies.
Full HVAC installation requires coordination of heating equipment, cooling components, ductwork design, and control systems to deliver efficient comfort at rated capacity. Our technicians perform Manual J and Manual D calculations, size equipment to match your structure, and commission the system to manufacturer standards.
Installing a mini-split system correctly requires precise wall penetration, vacuum-sealed refrigerant lines, and proper electrical isolation between indoor and outdoor units. Our technicians size each zone independently using BTU calculations to ensure consistent temperature control across every room.
When a mini-split displays error codes, produces weak airflow, or fails to reach setpoint, the fault often lies within the inverter board, thermistor sensors, or refrigerant circuit. Professional repair restores rated SEER output and eliminates the inefficient short cycling that drives up utility costs.
Heat pumps rely on a precise balance of refrigerant pressure, electrical components, and airflow to deliver efficient heating and cooling year-round. Professional repair addresses compressor hard starts, frozen coils, faulty thermostatic expansion valves, and auxiliary heat lockout conditions.
Selecting the right heat pump means matching BTU capacity to your structure while accounting for climate zone, insulation levels, and existing ductwork. Professional installation ensures proper refrigerant charge, correct defrost timing, and verified auxiliary heat staging for demanding winter conditions.
Professional AC tune-ups follow a multi-point inspection protocol covering thermostat calibration, condensate drain clearing, electrical connection tightening, and evaporator coil cleaning. Maintaining clean coils and proper superheat readings keeps your system running at peak rated efficiency.
Clean ductwork directly impacts the efficiency of your HVAC system by reducing static pressure and allowing unrestricted airflow to every register. Our technicians inspect for microbial growth, seal access points after service, and verify airflow improvements with anemometer readings post-cleaning.
Leaking and disconnected ductwork wastes up to 30 percent of conditioned air before it reaches living spaces, forcing your HVAC system to work harder and driving up energy costs. Professional duct repair seals joints, replaces damaged sections, and restores proper static pressure balance.
Maintaining safe and efficient boiler operation requires precise attention to water chemistry, flue gas temperatures, and combustion efficiency. Professional repair addresses leaking heat exchangers, malfunctioning aquastats, air-bound radiators, and ignition system failures to restore rated AFUE output.
A dryer that takes multiple cycles to dry clothes or feels excessively hot to the touch signals a restricted vent line. Technicians clear lint accumulation using rotary brush systems and compressed air, then verify exhaust velocity meets manufacturer specifications for safe, efficient operation.
Restoring reliable air conditioning performance requires more than replacing visible parts. Technicians measure refrigerant pressures, check compressor winding resistance, test run and start capacitors, and verify condenser fan operation to ensure every component of the cooling circuit functions within specification.
Professional smart thermostat installation goes beyond mounting and Wi-Fi pairing. Technicians verify your system has the necessary common wire, confirm compatibility with multi-stage heating and cooling equipment, and program setpoints and schedules tailored to your household for immediate energy savings.
When your heating or cooling system fails unexpectedly, rapid diagnosis is critical to minimizing discomfort and preventing secondary damage like frozen pipes or heat-related illness. Emergency technicians isolate the fault, whether electrical, mechanical, or refrigerant-related, and execute repairs on the spot.
KIC Refrigeration has proudly served communities like Kelso (pop. 12,739) since 2013, delivering HVAC solutions that combine NATE-certified expertise with high-efficiency equipment from top-tier manufacturers. Our technicians understand the specific heating and cooling demands that Washington weather places on residential and commercial systems across the region, and they arrive prepared to handle them.
Every HVAC project in Kelso, WA starts with a comprehensive system evaluation — including static pressure testing and refrigerant analysis — and ends with a verified comfort check. We install equipment with SEER2 ratings up to 22 and AFUE ratings above 96 percent because the efficiency of the system matters just as much as the skill of the technician installing it.
What makes us different from every other heating and cooling company in the area.
Every technician carries EPA Section 608 Universal certification for refrigerant handling — required by federal law for working with R-410A, R-22, R-32, and all regulated refrigerants. Your system is serviced by technicians who handle refrigerants legally and responsibly.
If the repair does not solve the problem or the installation does not perform to specification, we come back and make it right at no additional cost. Our guarantee covers workmanship, parts, and system performance because half-finished work is not in our vocabulary.
You receive a written estimate with itemized parts and labor costs before any work begins, and the final invoice matches. No diagnostic fees hidden in the repair bill, no surprise surcharges — just honest pricing you can verify and trust.
Most service calls are completed the same day you call. Our trucks are stocked with over 200 common parts — capacitors, contactors, ignitors, flame sensors, motors, and control boards — so we resolve the majority of repairs in a single visit without waiting on parts.
We carry full general liability and workers compensation coverage on every job. Our HVAC license is current in every state we operate, and we pull permits when local codes require them. Your property and our crew are fully protected on every visit.
Common questions about HVAC service, costs, and what to expect when you call.
The ideal time for HVAC replacement in Kelso is during the shoulder seasons — spring and fall — when demand is lower, equipment availability is highest, and scheduling is more flexible. Contractors are less booked during these periods, which means faster installation timelines and potentially more competitive pricing. You are also more likely to find manufacturer rebates, utility incentive programs, and promotional financing during off-peak months. From a technical standpoint, moderate temperatures allow your new system to be commissioned and tested under less extreme conditions. However, KIC Refrigeration completes HVAC installations year-round in Washington and can often start within days of your approved estimate, even during peak summer or winter demand. If your current system is showing signs of failure, do not wait for the perfect season — a planned replacement is always better than an emergency one.
Yes. The EPA estimates that Energy Star certified smart thermostats save Kelso homeowners an average of 8 percent on heating and cooling costs annually, which translates to $50 to $150 per year for a typical household. Models from Ecobee, Nest, and Honeywell Home use occupancy sensors, geofencing, and learning algorithms to build a schedule around your actual habits, automatically lowering temperatures when you leave and restoring comfort before you return. Many smart thermostats also provide energy usage reports, filter change reminders, and maintenance alerts that help you keep your system running efficiently. Some Washington utility providers offer rebates of $50 to $100 on qualifying smart thermostat purchases, further reducing the cost. KIC Refrigeration installs and configures smart thermostats to communicate properly with your specific HVAC system — including multi-stage equipment and heat pumps that require specialized wiring.
KIC Refrigeration installs and services all major HVAC equipment manufacturers in Kelso including Carrier, Lennox, Trane, Daikin, Goodman, Rheem, York, Bryant, American Standard, Mitsubishi, and Fujitsu. For ductless mini split systems, we specialize in Mitsubishi, Daikin, and Fujitsu units which are the market leaders in inverter-driven technology. We are not locked into a single manufacturer or distributor, which means our recommendations are based entirely on what best fits your home size, budget, efficiency goals, and existing infrastructure. Each brand offers different warranty structures, SEER2 ratings, and feature sets — from basic single-stage units to premium variable-speed communicating systems. Our NATE-certified technicians install every unit strictly to manufacturer specifications and register all warranties on your behalf.
Most HVAC installations, major equipment replacements, and significant ductwork modifications in Kelso require a mechanical permit from the local building department. This applies to furnace and air conditioner replacements, heat pump installations, boiler swaps, and new ductless mini split systems. Minor repairs like part replacements and refrigerant recharges typically do not require permits. KIC Refrigeration handles all permitting, code compliance documentation, and scheduling of final inspections on your behalf — you do not need to visit any government office or coordinate with inspectors. Permits exist to ensure your system is installed safely and to code, which protects your home and preserves your equipment warranty. Unpermitted work can create liability issues and complicate future home sales. We ensure every project meets current Washington mechanical codes and International Mechanical Code standards.
Yes. KIC Refrigeration provides around-the-clock emergency heating and cooling repair throughout Kelso and surrounding Washington communities. Whether your furnace fails during a cold snap and pipes are at risk of freezing, your air conditioner dies during a dangerous heat wave, or you detect the smell of gas near your equipment, our technicians respond quickly. Every service vehicle carries common replacement parts — capacitors, contactors, ignitors, blower motors, control boards, and refrigerant — so most emergency repairs are completed in a single visit. We do not charge extra trip fees for after-hours calls, and our dispatchers are trained to triage situations over the phone so the right technician arrives with the right equipment. Call us anytime and we will have a crew on the way.
HVAC repair costs in Kelso typically range from $150 to $500 for minor fixes such as capacitor replacement, contactor swaps, or thermostat wiring issues. Mid-range repairs like blower motor replacement or refrigerant recharging run $500 to $1,200. Major repairs — including compressor replacement, heat exchanger repair, or evaporator coil swap — cost $1,200 to $2,500 or more depending on equipment brand and system type. The final price depends on whether you have a furnace, heat pump, air conditioner, boiler, or ductless mini split, as parts and labor vary significantly between system types. Our NATE-certified technicians diagnose the issue accurately on the first visit, and KIC Refrigeration provides a written estimate with transparent pricing before any work begins. We never charge a diagnostic fee when you proceed with the recommended repair.
Thousands of satisfied customers — here is what a few of them had to say.
"KIC Refrigeration has serviced our commercial HVAC system for two years now. Always professional, always on time. Would not trust anyone else."
"KIC Refrigeration installed our new heat pump system and the difference is incredible. Our energy bills dropped noticeably the very first month."
"HVAC inspection was very thorough. Got a written report with photos and recommendations prioritized by urgency. Helpful for budgeting repairs."
We also serve these nearby communities with the same certified HVAC expertise.